![Hamish Erskine](/img/default-banner.jpg)
- 11
- 937 824
Hamish Erskine
United Kingdom
Приєднався 30 бер 2008
Hamish Erskine is a self-employed plumber, now working in Salisbury, UK. He specializes in plumbing repairs, including repair and replacement of toilets, taps, showers, radiators, washing machine plumbing, leaks, blockages and drains.
Video tour of 4 bed student house in Portland Street, Exeter
An excellent student property with 4 double bedrooms, 1 bathroom, additional cloakroom toilet, lounge, modern kitchen with breakfast bar that seats 4, separate dining room which also serves as a great communal study area, attractive rear garden with paved area, and large bicycle shed with access via rear gate. Kitchen fully equipped with washing machine, tumble dryer, dishwasher, tall fridge freezer, gas hob, electric oven, and microwave. Double glazed throughout, gas central heating, lovely warm house. 5 minute walk from Waitrose supermarket, ideally situated for St Luke's Campus and Peninsula Medical School students. Also just 10 minutes walk from city centre/Princesshay. Excellent communal space, and no ground floor bedrooms. Rent includes Water, Gas, Electricity, 1GB Broadband, and TV licence. Private local landlord, no agency fees, 48 week contract. Property to be let as a whole on a joint tenancy agreement. Available each year from start of September.
Переглядів: 82
Відео
Install of a Q-Fit Kitchen tap from the 1810 Company
Переглядів 6 тис.6 років тому
Hamish the Plumber reviews and installs a new Q-Fit kitchen tap made by the 1810 Company. The Q-Fit designs allows installation from above the worktop, achieving what Bristan intended with its Easyfit design but without any of the problems that beset Bristan's design. For further information about these Q-Fit taps, visit www.the1810company.co.uk
Problems with Bristan Easyfit Kitchen Taps - Overview
Переглядів 27 тис.7 років тому
A short overview of why Bristan Easyfit Kitchen taps pose a serious flood risk to people's properties, and what to do urgently if you have one.
Problems With Bristan Easyfit Kitchen Taps - Part 3
Переглядів 17 тис.7 років тому
With the help of Bertie (Albert Erskine), Hamish the Plumber suggests a redesign of Bristan’s Easyfit kitchen taps that might prevent future models from flooding people’s houses, and he continues his call for Bristan to make a product recall of the 2014 to 2016 models which use grub screws to secure the tap to its base.
Problems with Bristan Easyfit Kitchen Taps - Part 2
Переглядів 20 тис.7 років тому
With the help of Bertie (Albert Erskine), Hamish the Plumber examines where the design flaw lies in Bristan’s range of Easyfit kitchen taps. This is Hamish and Bertie’s first ever video together!
Problems with Bristan Easyfit Kitchen Taps - Part 1
Переглядів 75 тис.7 років тому
Hamish the Plumber reviews problems he has been having with Bristan's Easyfit kitchen taps falling off and flooding people's kitchens. For further information and recent updates, please visit bristan-easyfit-reviews.co.uk
How to fix a dodgy tap that won't turn on properly
Переглядів 636 тис.8 років тому
Hamish the Plumber demonstrates how to fix a dodgy basin tap that won't turn on properly. Watch in real time as he services the tap valve so that it works again like new.
How to unblock a basin
Переглядів 33 тис.8 років тому
Hamish the Plumber demonstrates how to unblock a basin using his 'mega-plunger' (a Rothenberger Ropump Super Plus) and a flexible hair catcher.
How to convert a toilet to dual flush
Переглядів 121 тис.8 років тому
Hamish the Plumber upgrades a lever toilet to dual flush and explains step-by-step what he is doing.
Cloakroom upgrade
Переглядів 1,2 тис.9 років тому
Video of a cloakroom upgrade I completed in an old Georgian house
Excellent, 👍
Thank you so much, I’m useless at plumbing but this was a perfect guide to solve this exact problem. Thought it was an airlock but after doing this it works like new. Legend 👍
Sorry mate. You found the AREA of the problem, but not the cause! In your video, you threw away the actual cause at 2' 15". What happens is that the chamber above the washer-body fills with water (which you threw away), and when you try to open he tap, it locks up, because water is incompressible and it has nowhere to go. Had you simply re-assembled the tap, after discarding the water, it would have functioned correctly, for a while. No need to clean up and polish the inside at all! The problem is that this will keep on happening, over and over again. I used to have this problem on an older set of taps and thought I'd cured it when I changed to new tap bodies; and I did, but have now had to change the bodies again and the problem has returned. I need to find a way to let the water out of the chamber above the valve. I believe that the water gets in (I only ever have this problem with the hot tap) after running the hot tap and as it cools, the air inside the chamber contracts, drawing in a small amount of water, which stays there. After repeated uses, the chamber eventually fills up enough to lock the tap, preventing the washer holder rising up into the chamber, which is now partially filled with water. I am first going to try removing the O-ring that seals the chamber. If that works without causing any problems, I'll look for a longer term solution, like maybe a relief groove/hole of some sort. That is the cause of the problem; not dirt, or roughness.
Looks like the base is at fault. I've fitted surface mounted showers with the same system. Not a problem.
Ha! Hi Hamish. It,s ok my wife fixed the tap. What a surprise.
I've fit loads of these taps. The trick is to do up the grub screws nice and tight 😅
Your using your pump pliers backwards
Hi Hamish, this happened to me today with a tap I fitted about 6 months ago! Was stunned to find your video with my exact tap and exactly the issue I had, thankfully I was home so minimal damage, but still very scary. Will take the advice of the comments and use some loctite. Thank you for bringing this to attention, astonishing that this video is nearly 8 years old and this issue still happening.
Very helpful video as I was about to buy one of these taps.
Greece the black rubbers first .It looks like they aren't pushed on enough .
Just put a dab of threadlock on the grub screw to prevent it from turning.
Thanks for that Hamish. Just what I was looking for. Neither taps turned on at all. Now they do :)
I had put one together "without turning anticlockwise" and it would not turn on. After carefully watching this video I was able to fix it in a couple of minutes. Lifesaver! He made a subscriber out of me.
Just put loctite blue on grub screws.
And here was I trying to undo the flexi tails from underneath, not a chance, another attempt this weekend now that I know what the crack is, Thanks, Hamish 🙂
Worked a treat on my bathroom hot tap! Thanks.
Thank you Hamish, l fitted a easy fit echo in about 2020 so far it's been fine, but now I'm aware that the grub screws can become lose I'll check them regularly, thanks again Hamish you seem like a real nice person .regards Martin from Tamworth
Dear Hamish great videos - now 2023 and I want to install this tap BRISTAN ECHO EASYFIT MONO MIXER KITCHEN TAP CHROME do you think is OK now :)
Thanks mate. Would never have figured out that grit was the problem. Sorted out an annoying kitchen tap finally! 5 ⭐ for you.
Thanks. You’ve solved my identical problem. Delighted.
Instead of silicone grease, can u use vaseline
good demo, but my heads spinning because of the spinning camera 😅
Thank you - very understandable explanation. I'm replacing my Bristan Easyfit kitchen tap - can you recommend a different manufacturer please
Good video, thanks 👍
Who runs your Fan Club, and what's the address?
Your smile could power the electricity for entire cities. And you happen to be a plumber, too. Two advantages in one. If you're not taken, ladies, form an orderly queue. If you are... lucky wife!
Hi Hamish. I have just fitted a new Echo easy fit Mixer for my friend in Crediton. I found this video after fitting it. It was for a friend, so obviously I am a little concerned. Have they modified the tap since your issues? I checked the grub screws and tightened them up super tight! Any ideas or suggestions on how I can avoid this dismounting issue from happening please. Cheers B
Be very careful not to overtighten the grub screws for fear of stripping the threads.
I have one of these in my kitchen. This far there have been no grub screw issues BUT I find that the cartridges lasted about 5 years and 1 month. Bloody ridiculous.
Fitted about 5 of these easy fit taps by Bristan and two blew off the sink !! Very fortunately for me both customers were home and had the intelligence to turn off the water They are absolute garbage Do not install them !!!
Brilliant! Just fixed one of my bath taps with this. Had no water coming out of it at all and it's fully functional again now 😁
Fantastic, cheers Hamish. I've just done both of the kitchen taps and they're working perfectly. They had been driving me mad for ages. 👍🏻
Thank you , i was looking for fixing a dripping easy fit tap and came across your video, my tap had the triangle grub screws and was the first version of this tap , tap has been removed today and different make fitted , Bristan tap in the bin !
Just saved us a trip to B&Q on a Saturday just by showing us the internal workings, the tap is now working again.
Thank you, Hamish 🙏🏼
This just happened to me (July 2023). The Echo tap was fitted 2 months ago. The tap had come loose from the base last weekend and I was going to call the plumber. Monday morning the tap blew off. The plumber blamed me, that I must have knocked it. Bristan blamed the plumber. All very unprofessional and unhelpful.
They have now modified design
Thanks, just solved an irritating tap that's bugged me for months.
Absolute garbage! Do not buy one of these taps
Can I use vaseline instead of that silicone thing you used?
Thanks Hamish - worked perfectly, exactly as you described.
Hamish, have you made a video update 2023 regarding the problems with these easyfit taps?
Great job Hamish i have replace the washer 3 times, now i know where the problem is
Please help me how to remove bottom part which you’re cleaning
Thanks Hamish for your excellent trilogy of videos! I bought a Bristan Echo easyfit a couple of days ago having read the ease of fitting reviews on the ScrewFix website. Then when I came to fit I came across your comments about some of the known problems with these taps. At this point I regretted my decision to purchase the Bristan but I was by now committed. Old tap was off. Water was off.....so I was in a way too far into the job to turn back! Decided to go ahead anyway. The so called push fit connector is an updated one with much improved grub screws having a conical point and running into drilled holes in the base. The overall quality of the unit is good, and Its heavy and well made. The fitting of the push fit connector was however not without complications and I think maybe the word Easyfit should be considered with caution. My connector would'nt go through the sink top hole....the sink is a composite one and quite thick. So I had to split the connector and feed part of it up from underneath. I'm not as young as I was and this was an awkard and difficult thing for me to execute! However everything is now together and working. I've used studlock on the grub screws. The tap looks nice but frankly I wouldn't recommend these taps at all. It's a brilliant concept poorly executed. I will keep an eye on the grub screws but have to say why am I feeling I have to maintain a kitchen tap? I will definitely shut them off when we go away....which basically means I have reservations about their efficiency and safety. Which is in itself a poor reflection on Bristan. At this point I am thinking I will keep this tap for maybe a year and then change it.....just really for peace of mind!
First Rate Hamish, that's exactly what I'll ask the plumber to do, when he calls, this Friday.
Guess what, following a recent event where a tap I installed released itself and caused a lot of damage I decided to speak to Bristan to report the incident!! They immediately said it was an installer error and that my reference to these videos and proof the taps were failing was rubbish, they apparently investigated every tap installed referred to in these videos and every single installation was wrong, all were incorrectly installed. They requested a copy invoice proof of purchase and full photos of the tap base and installation!!! Guess I will be looking for a new manufacturer of taps going forward then for all my projects 😞
I am so worried, I have fitted so many of these easy fit Bristan taps and the first one has just blown off causing havoc and drowning the clients and their kitchen, TV is gone, the dishwasher and a whole load of damage, very concerning and time to stop supplying these taps.
I just found this, I have installed so many of these taps I m now very worried, I was not too far from the client when I received a panic call saying the tap head has blown off, they panicked and eventually turned off the water main in the street but there the place was flooded big time and they are very stressful clients in anyway :-( Completely mystified about how this happened I spent four hours cleaning and drying everything but leaving and whilst the client appreciated the effort they are not happy and I am concerned at the consequences, this tap was fitted 6 months ago and I know 100% how tight I did the grub screws up as I do with all installations, I picked the tap from the sink only to find them almost out of their sockets!!! I guess I will be calling Bristan after the Bank Holiday as a matter of urgency. Do you know if there have been any amendments or updates to the design since this video? Thank You.
If time is not a concern then you can also leave the valve to soak in descaler for 30 mins